Automatic Miniaturization Desktop Full Edge Searching Actual Engraving H500CCD Model Lettering Film Engraving Machine Advertising Self-Adhesive Die Cutting Plot

Jinan Yuntu CNC Equipment Co., Ltd. / 2022-06-27

After-sales Service：Long-Term Support for The Software and Machine Mai
Warranty：The Whole Machine , Parts Are Guaranteed for One Y
Classification：Single-blade Cutter
Driven Type：Electric
Type：Industrial Cutter
Blade Material：Stainless Steel

=== Base Info ===

Model NO.：H500 CCD
Computerized：Computerized
Cache Capacity：4MB
Cutter Pressure：0-500g
Cutting Speed：0-800mm,S
Cutting Length：Unlimited
Product Name：Plotter Cutter
Voltage：110V,240V
Paper Feed Width：400mm
Cutting Width：300mm
Transport Package：Carton
Specification：long90CM*wide22CM*high14CM weight: 16.1KG
Trademark：yuntu
Origin：Jinan City, Shandong Province, China
HS Code：3701100000
Production Capacity：50000

=== Description ===
Camera computer full automatic edge inspection lettering machine
engraving machine H500 type Die cutting plotter H1380 1300mm 1200mm XP system,WINDOWS 7 32 bit ,64 bit Overhead, 6X2 character LCD display, touch navigation keyboard Main shaft double high torque motor, 16 subdivision drive Electronic limit, arbitrary origin setting 0--- 800 mm/s Unlimited 0---500G(Adjust at will) 0.05mm <+-0.1MM Various types of water-based, oily, atomic pens, poster pens with a diameter of 11.5MM HP--GL--PL/DM--PL Standard RS232(string)/ USB AC11V /240V±10%,52HZ 120W temperature :+5-+35,Relative temperature 30%-70% 108*22*14CM 156*22*14CM 111*32*35CM 165*32*35CM 18.05KG 25.25KG Q:Why is the pattern deformed or incomplete? 1. More pressure or too long blade tip or too dirty platen or too soft stickiness,
all of these factors can cause more resistance to the two faces of paper and make it fall behind the roller rotating, thus result in
deformed pattern. 2. The software setting isn't proper. (The tool compensation value is too big) 3. The carriage belt is too loose,
or the metal roller can't exactly follow the motor running. 4. The motor doesn't run all the steps. 5. The pattern is normal but not
complete, this may be resulted from too small tool compensation value.
Q:Why does the machine plot abnormally? 1. Software setting is not matched to the machine, so you must adopt proper
commands set or set proper tool compensation value. 2. The plotting software is suddenly broken up. 3. Plotting software has
been damaged or there is virus in computer.
Q:Why does the paper run deviation? 1. The stickiness isn't placed right. 2. The platen is too dirty so that the resistance from
two sides can't be balanced when the paper is moving. 3. The pinch rollers have been deformed or don't match to each other.
4. The pressure of the pinch roller is a little smaller and the paper is very sensitive to the external force. 5. The balance of the
stickiness weight isn't very good.
Q:Why some parts of letters are missing? 1. The vinyl is too heavy or too tightly wrapped. Metal roller might be soiled by
some foreign substance or by vinyl chips. 2. Cutting speed is too fast, cutting force is too great, or cutter tip is too long. 3.
Synchromesh belt is too tight, or pinch roller is under too much pressure. 4. Metal roller is faulty. Contact local distributor for
repairs and replacement. Q:Why different letters on the same line are cut to different depths? 1. Cutter holder is not tightly
attached. It should be tightened. 2. Cutter blade is not tightly set in the holder.
Q:Why letters appear to have ripples? 1. Cutting speed is too fast. Except for cutting large letters, speed should not exceed
80mm/s. 2. Cutting blade is of poor quality, or it has been damaged. Replace it. 3. Cutter holder is not tightly installed. Tighten
screw. Cutting small letters When cutting small letters, cutting speed and force should be adjusted to the lowest setting. Similarly
cutter tip should be adjusted to as short as possible. Cutting large letters Cutting speed and force may be increased to higher
settings. When cutting large letters Sharp Angle in Artcut software may be ignored.